PWC Forum: The best hang-out for Personal WaterCraft enthusiasts - View Profile: T0MMY B0NES

T0MMY B0NES T0MMY B0NES is offline

Member

  About Me

  • About T0MMY B0NES
    Location
    Nashville, TN
    Type of PWC
    Yamaha XLT 800 x2
    Disable Sidebar in Forum View
    Enable

  Statistics

Total Posts
General Information
  • Last Activity: 10-15-2019 03:21 PM
  • Join Date: 06-06-2019
  • Referrals: 0

  Mentions

No results to display...

  Quotes

10-14-2019
09:23 PM - Dave in DE quoted T0MMY B0NES in post 2003 Yamaha XLT 800 66e Projects
M8x55, not sure where I got the ...
09-13-2019
04:25 PM - T0MMY B0NES quoted Dave in DE in post 2003 Yamaha XLT 800 66e Projects
Are you using a piston to push ...
03:02 PM - Chris996 quoted T0MMY B0NES in post Hello and a few XLT 1200 questions.
DAVE IS THE MAN!!!! Chris, Da...
09-12-2019
11:30 AM - T0MMY B0NES quoted Chris996 in post Hello and a few XLT 1200 questions.
Ha! I was just going to ask a...
09-09-2019
11:04 PM - T0MMY B0NES quoted Dave in DE in post 2003 Yamaha XLT 800 66e Projects
Use a .003/.004 feeler guage be...
09-04-2019
06:45 PM - Dave in DE quoted T0MMY B0NES in post 2003 Yamaha XLT 800 66e Projects
It was a WSM kit purchased from ...
09-03-2019
06:31 PM - T0MMY B0NES quoted Dave in DE in post 2003 Yamaha XLT 800 66e Projects
Ok, I see now. I've done it bot...
04:59 PM - T0MMY B0NES quoted Dave in DE in post 2003 Yamaha XLT 800 66e Projects
"Then it's off to wrestle the r...
08-27-2019
07:27 PM - T0MMY B0NES quoted Dave in DE in post 2003 Yamaha XLT 800 66e Projects
Nothing should change the 1.2 w...
08-20-2019
04:21 AM - Dave in DE quoted T0MMY B0NES in post 2003 Yamaha XLT 800 66e Projects
And I was either shorted a check...
08-19-2019
04:21 PM - Dave in DE quoted T0MMY B0NES in post 2003 Yamaha XLT 800 66e Projects
You'll also need to get the pack...
03:41 PM - T0MMY B0NES quoted Dave in DE in post 2003 Yamaha XLT 800 66e Projects
You'll also need to get the pac...
08-18-2019
12:07 AM - Dave in DE quoted T0MMY B0NES in post 2003 Yamaha XLT 800 66e Projects
It is 3mm, my only qualm was the...
08-13-2019
11:13 PM - T0MMY B0NES quoted Dave in DE in post 2003 Yamaha XLT 800 66e Projects
First try a flat faced punch an...
08-12-2019
07:36 PM - Dave in DE quoted T0MMY B0NES in post 2003 Yamaha XLT 800 66e Projects
Reading up on these carbs, while...
03:59 PM - T0MMY B0NES quoted Dave in DE in post 2003 Yamaha XLT 800 66e Projects
1/8" is what I used. But factor...
02:34 PM - T0MMY B0NES quoted rodsatheart in post Big John
Nice job, and 40 is cheap. Go ah...
07-31-2019
06:27 PM - Dave in DE quoted T0MMY B0NES in post 2003 Yamaha XLT 800 66e Projects
Dave: Any issues with proceedin...
07-15-2019
04:32 PM - T0MMY B0NES quoted Dave in DE in post Carbs? CARBS!!!
Have you ever rebuilt a carb? ...
11:27 AM - T0MMY B0NES quoted rodsatheart in post 2003 Yamaha XLT 800 66e Projects
Took care of it. Only thing I ca...
 
For the best viewing experience please update your browser to Google Chrome